Battery capacity is measured in Amp-Hours. When registers are not displayed in engineering units, the value shown for Taper Current includes all 8 bits of this register represented in hex. TI is not responsible or liable for any such statements. Concerning EVMs including detachable antennas Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada. It’s a community-based project which helps to repair anything.

Uploader: Maugore
Date Added: 3 May 2016
File Size: 50.25 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 97688
Price: Free* [*Free Regsitration Required]

It’s a community-based project which helps to repair anything. The BL-5J in the N has a capacity of 1. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.

There are two separate circuits on the EVM module. If selected as an output, the open drain output can be set to on or off.

bq27200 Single Cell Battery Fuel Gauge Evaluation Module User’s Guide

Indirect is when there is no direct hardware way to perform an action, and some part of the system has to be made to do this without the user explicitly turning it on. Further, the user indemnifies TI from all claims arising from the handling or use of the goods.

In others, minor changes to their behaviour, that might even make their experience better, may greatly change battery life. Set of support documentation 1. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference.


This command is intended for manufacturing use. Among the selections are: These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. The system load and charger connect across J and J This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Direct power use is quite simple. Enter the name of the data log file in the Name Datalog File box 4. If the wireless router, and the N are setup correctly, then wifi is a very useful aid to debugging. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions.

To reduce potential bxttery interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e. Personal tools Log in.

LKML: Anton Vorontsov: Re: [PATCH] power: support for Texas Instruments BQ27x00 battery managers.

This application turns on the LED Flash so the user can see. However, there is no guarantee that interference will not occur in a particular installation.

The below is the result of sshing into the N, and running the script. It should not be used as all or part of a finished end product.


N software power management – wiki

Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications.

One is the active bq fuel gauging circuitry; the other is the logic and power control to program the on-chip configuration EEPROM of batterry bq User training is very important, in some ways more important than the rest of this guide.

Also, please do not transfer this product, unless you give the same notice above to the transferee. Click on the Open button 5.

Unless otherwise indicated, this EVM is not a finished electrical equipment and not intended for consumer use. Operation is subject to the following two conditions: The bqEVM is now set up for operation.

File Start Data Log from the pull-down menu. Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law nq27200 Japan.

As with all electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development environments should use these EVMs.